70-410 Dumps PDF | 100% Pass Guarantee on 70-410 Exam

There’s no higher study material than MCSE dumps as a result of its shown 100 percent result. It’s become the highest priority of IT students. It’s not thus tough currently to pass exam with the assistance of 70-410 study guide. Irresponsibleness and credibility of this material can't be challenged. All the queries and answers developed and compiled by the qualified consultants. To-the-point info has been crammed in the 70-410 Question Answers of the exam necessities, you'll simply pass your certification by the primary try if you study sensible in line with the directions of the consultants at Dumps4Download. You’ll bring the simplest of your results if you set your sincere efforts on dumps. This material is obtainable to be downloaded in PDF kind however before downloading a full file you'll check 70-410 Dumps PDF freed from price. what is more, if you would like accuracy and check of you learning then you'll download at on-line test engine when finishing your study material.

Demo Questions:

Question: 1

You have a server named Server1 that runs Windows Server 2012 R2. Server1 has the Hyper-V server
role installed.
An iSCSI SAN is available on the network.
Server1 hosts four virtual machines named VM1, VM2, VM3, and VM4.
You create a LUN on the SAN to host the virtual hard drive files for the virtual machines.
You need to create a 3-TB virtual hard disk for VM1 on the LUN. The solution must prevent VM1 from
being paused if the LUN runs out of disk space.
Which type of virtual hard disk should you create on the LUN?

A. Dynamically expanding VHDX
B. Fixed-size VHDX
C. Fixed-size VHD
D. Dynamically expanding VHD

Answer: B

Explanation:
The virtual disk needs to be a VHDX file since it is going to be over 2TB in size and it must be fixed-size so
that the space is already taken on the server (that way the server does not run out of space as the
volume grows) even if the actual virtual disk does not yet hold that amount of data.

Question: 2

Your network contains an Active Directory domain named adatum.com. The domain contains a member
server named Host1. Host1 runs Windows Server 2012 R2 and has the Hyper-V server role installed.
Host1 hosts two virtual machines named VM5 and VM6. Both virtual machines connect to a virtual
switch named Virtual1.
On VM5, you install a network monitoring application named Monitor1.
You need to capture all of the inbound and outbound traffic to VM6 by using Monitor1.
Which two commands should you run from Windows PowerShell? (Each correct answer presents part of
the solution. Choose two.)

A. Get-VM “VM6″ | Set-VMNetworkAdapter-IovWeight 1
B. Get-VM “VM5″ I Set-VMNetworkAdapter -IovWeight 0
C. Get-VM “VM5″ | Set-VMNetworkAdapter -PortMirroring Source
D. Get-VM “VM6″ | Set-VMNetworkAdapter -AllowTeaming On
E. Get-VM “VM6″ | Set-VMNetworkAdapter -PortMirroring Destination
F. Get-VM “VM5″ | Set-VMNetworkAdapter -AllowTeaming On

Answer: C, E

Explanation:
-PortMirroring specifies the port mirroring mode for the network adapter. This can be set to None,
Source, and Destination.
If set to Source, a copy of every network packet it sends or receives is forwarded to a virtual network
adapter configured to receive the packets.
If set to Destination, it receives copied packets from the source virtual network adapter.
In this scenario, VM5 is the destination which must receive a copy of the network packets from VM6,
which s the source.
Reference: http://technet.microsoft.com/en-us/library/hh848457.aspx

Question: 3

Your network contains two Hyper-V hosts that run Windows Server 2012 R2. The Hyper-V hosts contain
several virtual machines that run Windows Server 2012 R2.
You install the Network Load Balancing feature on the virtual machines.
You need to configure the virtual machines to support Network Load Balancing (NLB).
Which virtual machine settings should you configure?

A. DHCP guard
B. Port mirroring
C. Router guard
D. MAC address

Answer: D

Explanation:
http://social.technet.microsoft.com/Forums/windowsserver/en-US/5b3a0a9d-26a2-49ba-bbbe29d11fcbb7ce/nlb-on-hyperv?forum=winserverhyperv
For NLB to be configured you need to enable MAC address spoofing.

Question: 4

You have a print server named Server1 that runs Windows Server 2012 R2.
You discover that when there are many pending print jobs, the system drive occasionally runs out of
free space.
You add a new hard disk to Server1.You create a new NTFS volume.
You need to prevent the print jobs from consuming disk space on the system volume.
What should you modify?

A. The properties on the new volume
B. The properties of the Print Spooler service
C. The Print Server Properties
D. The properties of each shared printer

Answer: C

Explanation:
Windows spools print jobs by default to the following directory as they are processed:
%SystemRoot%\SYSTEM32\SPOOL\PRINTERS.
It is possible for the administrator of a Windows print server to manually instruct Windows the location
for placing the spool files, if for example there is a concern for disk space.


Question: 5

Your network contains an Active Directory domain named contoso.com. You need to create the Central
Store for Group Policy Administrative Templates in adatum.com
What should you copy?

A. C:\Windows\System32\GroupPolicy to \\Adatum.com\Policies
B. C:\Windows\PolicyDefinitions to \\Adatum.com\SYSVOL\Adatum.com\Policies
C. C:\Windows\System32\GroupPolicy to \\Adatum.com\Netlogon
D. C:\Windows\PolicyDefinitions to \\Adatum.com\Netlogon

Answer: B